223xs

Stereo 2-Way/Mono 3-Way Crossover with XLR Connectors

The secret to making speakers sound great lies with the crossover you use. With the dbx® 223xs Crossover you'll get great performance, ultra low-noise, rugged reliability and four decades of dbx knowledge and expertise in building the world's finest processors. The 223xs uses precision filters to separate the audio signal and direct the correct frequencies to your loudspeaker drivers. By directing only the specific frequency bands to each speaker driver the 223xs leaves your amplifiers free to use their full power on the usable signal eliminating distortion and giving your PA system a cleaner and better sound.

Frequency range: to 90 kHz; FREQUENCY RANGE
Dynamic range: >106 dB; DYNAMIC RANGE
Weight: 1.7 kg; WEIGHT

Supplied and supported in Pakistan by KYAF, the official HARMAN Professional distributor.

AT A GLANCE

Specifications

to 90 kHz
Frequency range: >106 dB
Dynamic range: 1.7 kg
Weight: Selects normal
Low-frequency driver: Balanced >50k Ω, unbalanced >25k Ω
Impedance: 1.75" H X 19" W X 6.9" D
Dimensions: XLR
Inputs: 90 kHz, +0/-3 dB
Frequency Response

Input Connectors	XLR (pin 2 hot)
Input Type	Electronically balanced/unbalanced, RF filtered
Input Impedance	Balanced >50k Ω, unbalanced >25k Ω
Max Input	>+22dBu balanced or unbalanced
CMRR	>40dB, typically >55dB at 1kHz
Output Connectors	XLR
Output Type	Impedance-balanaced/unbalanced, RF filtered
Output Impedance	Balanced 200 Ω, unbalanced 100 Ω
Max Output	>+21dBu balanced/unbalanced into 2k Ω or greater
Bandwidth	20Hz to 20kHz, +/-0.5dB
Frequency Response	90 kHz, +0/-3 dB
Signal-to-Noise Ratio	Ref: +4 dBu, 22 kHz measurement bandwidth
Signal-to-Noise (Stereo Mode)	>94dB (Low Output), >91dB (High Output)
Signal-to-Noise (Mono Mode)	>94dB (Low Output), >93dB (Mid Output), >91dB (High Output)
Dynamic Range	> 106 dB, unweighted, any output
THD+Noise	< 0.004% at +4 dBu, 1 kHz; < 0.04% at +20 dBu, 1 kHz
Interchannel Crosstalk	< -80 dB, 20 Hz to 20 kHz
Crossover Frequencies (Stereo Mode)	Low/High: 45 to 960 Hz or 450 Hz to 9.6 kHz (x10 setting)
Crossover Frequencies (Mono Mode)	Low/Mid: 45 to 960 Hz or 450 Hz to 9.6 kHz (x10 setting); Mid/High: 45 to 960 Hz or 450 Hz to 9.6 kHz (x10 setting)
Crossover Filter Type	Linkwitz-Riley, 24 dB/octave, state-variable
Low cut Switch	Activates 40 Hz Butterworth, 12 dB/octave high-pass filter, one switch per channel.
Phase Invert Switch	Inverts the phase at the output, one switch per output.
x1 / x10 Switch	Multiplies the low-high(mono: low/mid and high/mid) crossover frequency range of the front-panel markings by a factor of 1 or 10, one switch per channel.
Mode Switch	Selects stereo/mono and 2/3-way operation
LF Sum Switch	Selects normal (stereo) or mono-summed low frequency operation and disables Ch 2’s low output phase invert LED to indicate that this output is not operational in the LF sum mode.
Indicators	Stereo Operation (Green); Mono Operation (Yellow); Low Cut (Red-per channel); x10 (Green-per channel); Phase Invert (Red-per output)
Operating Voltage	100 VAC 50/60 Hz; 120 VAC 60 Hz 230 VAC50 HZ
Operating Temperature	32°F to 113°F (0°C to 45°C)
Power Consumption	15W
Power Connector	IEC receptacle
Dimensions	1.75" H X 19" W X 6.9" D (4.4cm x 48.3cm x 17.5cm)
Unit Weight	1.7 kg
Shipping Weight	2.5 kg

	223xs	234xs
Input Connectors	XLR (pin 2 hot)	XLR
Input Type	Electronically balanced/unbalanced, RF filtered	Electronically balanced/unbalanced, RF filtered
Input Impedance	Balanced >50k Ω, unbalanced >25k Ω	Balanced >50k ohm, unbalanced >25k ohm
Max Input	>+22dBu balanced or unbalanced	>+22dBu balanced or unbalanced
CMRR	>40dB, typically >55dB at 1kHz	>40dB, typically >55dB at 1kHz
Output Connectors	XLR	XLR
Output Type	Impedance-balanaced/unbalanced, RF filtered	Impedance-balanaced/unbalanced, RF filtered
Output Impedance	Balanced 200 Ω, unbalanced 100 Ω	Balanced 60 ohm, unbalanced 30 ohm
Max Output	>+21dBu balanced/unbalanced into 2k Ω or greater	>+21dBu balanced/unbalanced into 2k ohms or greater
Bandwidth	20Hz to 20kHz, +/-0.5dB	20Hz to 20kHz, +/-0.5dB
Frequency Response	90 kHz, +0/-3 dB	90 kHz, +0/-3 dB
Signal-to-Noise Ratio	Ref: +4 dBu, 22 kHz measurement bandwidth	Ref: +4 dBu, 22 kHz measurement bandwidth
Signal-to-Noise (Stereo Mode)	>94dB (Low Output), >91dB (High Output)	>94dB (Low Output), >93dB (Mid Output), >90dB (High Output)
Signal-to-Noise (Mono Mode)	>94dB (Low Output), >93dB (Mid Output), >91dB (High Output)	>94dB (Low Output, Low/Mid Output); >92dB (High/Mid Output); >88dB (High Output)

FOR DESIGNERS AND INSTALLERS

Downloads

dbx's own files, opened here on the KYAF site.

dbx 223xs — 223xs
Stereo 2-Way/Mono 3-Way Crossover with XLR Connectors

DESIGN

Everything at the back of the box.

FEATURES

What the 223xs brings.

The dbx 223xs is a dual channel crossover with all the features you would expect from a professional product. It features Linkwitz-Riley 24dB per octave filters, independent output gain controls for level matching, output phase inversion, 40 Hz low cut filter, and optional mono summing of the low frequency (subwoofer) output. Everything in the design exudes great precision from the solid "click" controls to the high quality XLR inputs and outputs.